Dhara Agency

Features:

• Loading accuracy as high as ± 1
• Straining at variable speeds to suit a wide range of materials.
• Printer & PC graphs enable study the behavior of the material.
• Motor driven threaded columns for quick effortless adjustment of lower cross-head-to facilitate rapid fixing of test specimen.
• Simplicity in reading because of digital readouts.
• Wide range of standard and special accessories, including load stabilizer
• Easy change from plain to threaded and screwed specimens.
• Large effective clearance between columns enables testing of standards specimens as well as structures.
• Simple controls for ease of operation.
• Robust straining frame of an extremely rigid construction.
• Safe operation ensured by means of safety devices.
• Fully enclosed and protected pressure transducer.
• RS 232 serial port to transfer data to computer for analysis/storage evaluation etc.
• Manual control & release valve operation.
• Load Capacity : 100 kN, 200 kN, 400 kN, 600 kN,1000 kN, 1200 kN, 1500 kN, and 2000 kN.

Additional Information:

• Item Code: UTE-10

• Capacity : Charpy : 300 Joule, Izod: 170 Joule.
• This is low cost Impact testing machine & it is specially designed for engineering colleges.
• This Machine conforms to IS 3766-1977, IS 1598-1977, IS 1757-1988,IS 1499-1977 and BS 131 Part I, II, III, IV. standard.
• This is simple & maintenance free machine.
• New modified Brake drum unit is provided to stop the pendulum swing instantly after test.
• Safety guard is provided for operator safety.

• Charpy Striker R2 mm - 1No.
• Izod Strike R0.75 mm - 1No.
• Charpy - Izod support Block - 1No.
• Specimen setting Gauges for Charpy & Izod - l Each.
• Allen key Set - 1 set.
• Instruction Manual - 1 No
• Model: FIT-300EN (ISO 148)

• The pendulum Impact Tester, Model IT-30 is designed for
• conducting Izod, Charpy test. The test methods confirm to
• BS:131:PART 4-1972 (Amended 15 Aug. 1993) BSEN:10045-
• 2:1993.
• The pendulum is mounted on antifriction bearings. It has two
• starting positions, the upper one for Charpy the lower one for Izod
• testing. On release, the pendulum swings down to break the
• specimen & the energy absorbed in doing so is measured as the
• difference between the height of drop before rupture of the test
• specimen and is read from the maximum pointer position on the
• dial scale.
• (It is read on digital readout in case of electronic machines).
• There are two strikers and one combined support anvil available
• for fitting in to the pendulum and on the base of machine for the
• Izod, Charpy test respectively. Changing from one striker to
• another is achieved simply by fixing the new striker into it’s
• position.
• The Charpy test piece rests on alloy steel support anvils, fitted on
• the base of the machine rigidly held in position by Allen screws.
• End stopper is provided for quickly and accurately locating the
• test piece centrally between the supports.

• The Izod Test piece is clamped vertically in Izod support fitted on
• the base of the machine. The support is provided with a machined
• vertical groove to suit the test piece size. The front clamp piece
• and the Allen screw enable clamping of the test piece in correct
• height with the help of Izod setting gauge supplied.
• Izod Test :
• The Izod Test piece is clamped vertically in Izod support fitted on
• the base of the machine. The support is provided with a machined
• vertical groove to suit the test piece size. The front clamp piece
• and the Allen screw enable clamping of the test piece in correct
• height with the help of Izod setting gauge supplied.

Additional Information:

• Item Code: IT30

• Precision AC servo motor & drive with ball lead screw gives an advanced drive system with 1 to 500 standard speed range.
• Provision for load cell interchangeability & thereby automatic selection of load full scale & Units (kN or N).
• Speed selection through data entry or variable speed through potentiometer.
• Facility for mounting different load cells & clamping devices to suit different tests & materials such as thin wires, metal sheets, fiber glass, leathers, springs, card boards etc.
• Built-in parallel interface to connect Dot matrix printer for data & curve print-out.
• Safety interlock for overload & limit switch sensing to ensure protection during test.
• Universal applications in R& D, Education, Quality control & Production for test like, Tensile, Compression, Bending etc.

• Front panel membrane type key board for machine with numeric keys for data entry.
• 7 segment display.
• Auto load cell identification.
• Data entry with numeric keyboard of test parameters including speeds, rupture % peak, pre load, modulus data,, test data & specimen data.
• 20 input data set storage, 50 result storage, maintains data & results during power off.
• Batch test facility for generating batch & statistics result using same data set.
• Optional remote to ease specimen loading/unloading.
• RS232C serial port. Optional windows based software available for-
• Online graph on PC. Data analysis, Statistics, Point tracing superimposing graphs to compare with standard, zooming graph etc.
Printer port for printer interface with-
• Graph & result print-out.
• Test Certificate print-out.
• Batch certificate print-out.
• Simple statistics print-out.